Chapter 12: BlueSecure Access Points

12-30

• Click to accept all the DynamicRF recommendations for

channel and power.The configuration will be saved to the database, and then

applied to the individual access point.

)

Note: The BSAP-1700 does not support dual mode or Dynamic RF, only Set Once

and Hold.

Enabled A BSAP is enabled when it has connected to the BSC and has downloaded its

configuration (either global settings or specific configuration). The downloaded

configuration must be set to enable the BSAP’s radios. Additionally, BSAP service must be

enabled on the BSC itself to enable BSAPs.

MAC The BSAP’s unique Media Access Control (MAC) address displayed six pairs of

hexadecimal numbers.

Radio MAC The MAC address of the BSAP’s 802.11/jointfilesconvert/443712/bg radio is listed if the BSAP has been polled

successfully since the last BSC reboot. To calculate the MAC address of the 802.11a/n

radio, add one to the b/g/n MAC address.

Hostname The BSAP’s configured hostname.

Location The BSAP’s configured location.

Status The BSAP’s current status. Possible values are:

• disabled - The BSAP has been administratively disabled.

• modified - The BSAP configuration on the BSC has been modified.

• updating - The BSAP is loading a new configuration from the BSC.

• up2date - The BSAP has loaded and is running its configuration stored on the BSC.

• busy - The BSAP is temporarily unable to report its status to the BSC due to system

activity.

Active This BSAP is connected to BSC, has downloaded its configuration, and is online as source

of wireless data traffic to the BSC.

Error The BSAP has reported an error condition.

Hardware BSAP model (BSAP-1500, BSAP-1540, BSAP-1700, BSAP-1800, and Wi-Jack Duo.)

Firmware The BSAP’s firmware version number.

)

Note: If you have selected but not yet upgraded to a new version of the firmware (either

globally for all APs or for an individual AP), the Firmware column shows two firmware

versions: the currently running firmware is displayed in black and the upgrade firmware

is displayed in red. This indicates that there is a mismatch between what is running and

what should be running. In addition, the following hint is displayed: “Firmware shown in

red is the active firmware. AP requires upgrade.”

Note: If you need to upgrade APs that are currently at 6.2 or earlier, you cannot use TFTP

to do so. TFTP is supported only at 6.3 or later.

Message Optimal Dynamic RF

)

Note: Sometimes when the channel is shown, a secondary channel is also shown, for

example (BG=11+7). The second channel is the MIMO secondary channel and is used

by 802.11n capable client devices.

1 2 ... 249 250 251 252 253 254 255 256 257 258 259 ... 375 376

Komentáře k této Příručce

Žádné komentáře

Warn 9 Series Hydraulic (3.0 cu in motor) Handbücher

Bedienungsanleitungen und Benutzerhandbücher für Für das Auto Warn 9 Series Hydraulic (3.0 cu in motor).
Wir stellen 1 PDF-Handbücher Warn 9 Series Hydraulic (3.0 cu in motor) zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung

Warn 9 Series Hydraulic (3.0 cu in motor) Bedienungsanleitung (2 Seiten)

Marke: Warn | Kategorie: For the car | Größe: 0.49 MB |

Inhaltsverzeichnis

WARN Industrial Winch

Weitere Produkte und Handbücher für Für das Auto Warn

Modelle	Dokumententyp
9 Series Hydraulic Round Top	Bedienungsanleitung WARN 9 Series Hydraulic Round Top User Manual, 2 Seiten
12 Series Hydraulic (Anti-clockwise)	Bedienungsanleitung WARN 12 Series Hydraulic (Anti-clockwise) User Manual, 2 Seiten
12 Series Hydraulic Round Top	Bedienungsanleitung WARN 12 Series Hydraulic Round Top User Manual, 2 Seiten
15 Series Hydraulic	Bedienungsanleitung WARN 15 Series Hydraulic User Manual, 2 Seiten
18 Series Hydraulic	Bedienungsanleitung WARN 18 Series Hydraulic User Manual, 2 Seiten
WG9 WINCH (Standard Drum)	Bedienungsanleitung WARN WG9 WINCH (Standard Drum) User Manual, 2 Seiten
WG9 WINCH (Long Drum) with remote clutch	Bedienungsanleitung WARN WG9 WINCH (Long Drum) with remote clutch User Manual, 2 Seiten
WG9 WINCH (Long Drum) with manual clutch	Bedienungsanleitung WARN WG9 WINCH (Long Drum) with manual clutch User Manual, 2 Seiten
RT15 PORTABLE WINCH	Bedienungsanleitung WARN RT15 PORTABLE WINCH User Manual, 3 Seiten
9.5cti Multi-Mount	Bedienungsanleitung WARN 9.5cti Multi-Mount Manuel d'utilisation, 20 Seiten
ZEON 10	Bedienungsanleitung WARN ZEON 10 User Manual, 12 Seiten
1500 AC	Bedienungsanleitung WARN 1500 AC User Manual, 30 Seiten
9.5cti Multi-Mount	Bedienungsanleitung WARN 9.5cti Multi-Mount Benutzerhandbuch, 38 Seiten
3000 ACI	Bedienungsanleitung WARN 3000 ACI User Manual, 144 Seiten
4700 DC	Bedienungsanleitung WARN 4700 DC User Manual, 127 Seiten
4000 DC	Bedienungsanleitung WARN 4000 DC User Manual, 126 Seiten
2000 DC	Bedienungsanleitung WARN 2000 DC User Manual, 126 Seiten
Tabor 12K	Bedienungsanleitung WARN Tabor 12K User Manual, 33 Seiten
9.5xp	Bedienungsanleitung WARN 9.5xp User Manual, 20 Seiten
Tabor 12K	Bedienungsanleitung WARN Tabor 12K Benutzerhandbuch, 33 Seiten

ADTRAN BlueSecure Controller Specifikace Strana 254

Komentáře k této Příručce

Související produkty a manuály pro Sítě ADTRAN BlueSecure Controller

Warn 9 Series Hydraulic (3.0 cu in motor) Handbücher

Warn 9 Series Hydraulic (3.0 cu in motor) Bedienungsanleitung (2 Seiten)

Inhaltsverzeichnis

Weitere Produkte und Handbücher für Für das Auto Warn